打膠機打膠不飽滿的原因及解決方法！
中空玻璃膠機從功能上講，非常簡單。專注于中空玻璃上膠，但中空玻璃上膠機在上膠過程中可能會遇到不全上膠的問題。今天，我們專門針對中空玻璃膠水機膠水不夠做介紹。
Hollow glass glue machine is very simple in function. Focus on the insulating glass gluing, but the insulating glass gluing machine may encounter the problem of incomplete gluing in the gluing process. Today, we specially introduce the insufficient glue of the insulating glass glue machine.
事實上，我們出現這個問題主要是由以下三個條件造成的!
In fact, we have this problem mainly caused by the following three conditions!
，上膠速度太快
First, the speed of glue application is too fast
一些客戶為了加快自己的生產節奏生產計劃后,調整密封劑認為速度太快,導致膠體仍沒有完全達到合格標準的頭已經到下一個位置膠操作,如果我們需要加速調整膠膠機運動參數,所以我們也要有相應的相應設置膠供應系統,如這一次我們需要增加供應壓力,增加上膠速度，使上膠機隨物體移動速度增加。如果我們只增加膠水機的速度，而不調整壓力，很可能是膠水不夠。
In order to speed up the production schedule, some customers adjust the sealant to think that the speed is too fast, so that the head of the sealant which still does not meet the qualified standard has been moved to the next position for glue operation. If we need to speed up the adjustment of the movement parameters of the glue machine, we also need to set the corresponding glue supply system, such as this time we need to increase the supply pressure, increase the glue speed Degree, so that the glue machine with the object moving speed increases. If we only increase the speed of the glue machine without adjusting the pressure, it is likely that the glue is not enough.
2. 供膠壓力不足
2. Insufficient glue supply pressure
事實上，這種情況在前一種情況中已經描述過了，即使不調整膠水機的速度也會出現打膠不滿的情況，那么有可能供應的膠水壓力太小。此時我們只需要調整上膠壓力就可以解決這個問題。
In fact, this situation has been described in the previous situation. Even if the speed of the glue machine is not adjusted, there will be insufficient glue application. Then it is possible that the glue pressure supplied is too small. At this time, we just need to adjust the glue pressure to solve this problem perfectly.
3.鼻子損壞傳感器
3. Nose damage sensor
這種情況非常罕見，但不能排除。在我們的中空玻璃上膠機的頭部，有一個傳感器可以檢測鋁帶的深度。如果鋁帶過深或過淺，會自動調節移動速度和上膠壓力(自動調節范圍小)。這可能會發生，如果我們的鋁帶本身是不同的色調，加上損壞我們的傳感器!
This is very rare, but it cannot be ruled out. At the head of our insulating glass gluer, there is a sensor that can detect the depth of the aluminum strip. If the aluminum strip is too deep or too shallow, it will automatically adjust the movement speed and glue pressure (the automatic adjustment range is small). This can happen if our ribbon itself is of different hues, plus damage to our sensors!
希望通過小編的表達可以在你的設備中找到這種問題的時候可以有效的解決問題，不用擔心這個問題。如果您對中空玻璃上膠機有任何問題，請隨時與我們聯系。
I hope that this kind of problem can be found in your device through the expression of Xiaobian, which can effectively solve the problem without worrying about it. If you have any questions about the insulating glass gluing machine, please feel free to contact us.
上一篇：怎么避免雙液點膠機硅膠中毒現象！
下一篇：點膠機的針頭與膠水使用時應該注意啥？
