關于中空玻璃自動打膠機的原理和構造
一、中空玻璃自動打膠機的原理和構造
1、 The principle and structure of insulating glass automatic gluing machine
中空玻璃自動打膠機是玻璃深加工設備中產生較晚但用量較大的機械設備之一。，主要作用是將半成品的中空玻璃做好密封，也可以作異形玻璃的密封。正確合理的使用中空玻璃自動打膠機，不僅能保證生產的正常進行，還會起到延長機器壽命的作用。中空玻璃打膠機總共分為三種：立式自動打膠機、臥式半自動打膠機、手動打膠機。
The automatic gluing machine for insulating glass is one of the mechanical equipment which is produced late but has large consumption in the glass deep processing equipment. The main function is to seal the semi-finished insulating glass, and also to seal the profiled glass. The correct and reasonable use of insulating glass automatic gluing machine can not only ensure the normal production, but also play a role in extending the service life of the machine. Insulating glass gluing machine is divided into three types: vertical automatic gluing machine, horizontal semi-automatic gluing machine and manual gluing machine.
中空玻璃半自動打膠機主要通過打膠機來實現中空玻璃的打膠。客戶可以根據自己需要的參數來設置中空玻璃半自動打膠機。
Insulating glass semi-automatic gluing machine is mainly used to realize the gluing of insulating glass. Customers can set the insulating glass semi-automatic gluing machine according to their own parameters.
臥式中空玻璃半自動打膠機通產是由打膠機、供膠機組成。每個廠家的價位不盡相同，因為不同的材料和電機會影響機器的精度和使用壽命。通常中空玻璃半自動打膠機的壽命為10—15年。
Horizontal insulating glass semi-automatic gluing machine is composed of glue making machine and glue supplying machine. Each manufacturer's price is not the same, because different materials and motors will affect the accuracy and service life of the machine. Generally, the service life of semi-automatic gluing machine for insulating glass is 10-15 years.
二、怎樣調試臥式中空玻璃半自動打膠機
2、 How to adjust the horizontal insulating glass semi-automatic gluing machine
放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯示屏上找到原點設定，點擊輔助原 點設定，然后點擊頭部原 點設定，注意原 點設定時避免頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值一致即可，注意設置時傳送帶上不要有玻璃。然后是混交了，按一桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，在按鏈接生產線，自動，自動運行，此時可以自動打膠。
Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected. First, turn on the air pump switch, the main power switch and the console switch. Press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. After setting, return to find the glass thickness setting. First, the thickness of the glass, then the aluminum spacer, and then the thickness of the glass. After input, click settings to enter. Wait for the command position to be consistent with the current position value. Pay attention to no glass on the conveyor belt when setting. Then, when mixing, press the button of a bucket of glue, press the button of work selection, and then press the button of tapping to start. At this time, when the glue head is pressed to release glue, when the white glue can not be seen, after mixing evenly, press the cut off button, and then press the link production line to automatically and automatically run. At this time, the glue can be automatically applied.
調試的注意事項：
Notes for debugging:
1、 在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the operation of the machine on that day, the glue in the hose should be flushed out to prevent hardening; if it is not practical for a long time, it is necessary to clean the hose and gun with kerosene.
2、 雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。
2. For silicone glue or polysulfide glue used in two-component gluing machine, the impurities should not be too high. The low-quality glue is easy to block the filter system of the rubber tube, resulting in poor or uneven glue output.
3、 在更換膠的品種時要特別注意把雙組份打膠機內殘留的膠沖凈，清洗，因為不同品種甚的膠容易反應堵塞機器。
3. When changing the type of glue, special attention should be paid to flushing and cleaning the residual glue in the two-component gluing machine, because different types or even brands of glue are easy to react and block the machine.
液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成安 全事故。
The pressure of the hydraulic station system can not be adjusted too high. According to the actual situation such as indoor environment temperature, adjust it to meet the normal glue output of the rubber nozzle and evenly apply glue. When opening the hydraulic station, the glue gun must be opened, otherwise the pipeline pressure of component B will rise very high, causing safety accidents.
上一篇：濟南雙組份打膠機的精度質量的標準
下一篇：雙組份打膠機必須遵循的幾大流程
