講解打膠機的安裝調試過程
打膠機可簡單分為，控制臺，吸盤，膠頭，挎板，掃描尺，打膠板。那么
雙組份打膠機的安裝調試過程是怎樣的呢？
The glue applicator can be simply divided into console, suction cup, glue head, sideboard, scanning ruler and glue applicator. What is the installation and commissioning process of the two-component glue applicator?
打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯示屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定，注意原點設定時避免頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值一致即可，注意設置時傳送帶上不要有玻璃。
Turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid the collision between the head and the auxiliary suction cup when setting the origin. After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer strip, and then the glass thickness. After entering, click the setting to enter. Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting.
然后是混交了，按桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，在按鏈接生產線，自動，自動運行，此時可以自動打膠。
Then it is mixed. Press the first bucket of glue button, press the work selection button, and then press the pat glue to start. Press the cut open button, and then the glue head will release the glue. When the white glue is not visible, press the cut off button after mixing evenly. Press the link production line, and it will run automatically. At this time, it can automatically apply glue.
開始打膠要看每條邊每個角打膠是否均勻，下面說下如何調整打膠機，在屏幕上點擊返回找到密封配方，點擊進入，會顯示當前密封壓力，如果每條邊都缺膠，那么可增加壓力，壓力大膠量大，壓力小膠量就小。
To start gluing, it is necessary to see whether the gluing is even at each corner of each side. Next, let's talk about how to adjust the gluing machine. Click back on the screen to find the sealing formula. Click enter, and the current sealing pressure will be displayed. If there is a lack of glue at each side, then the pressure can be increased. If the pressure is large, the amount of glue is large, and the pressure is small, the amount of glue is small.
下面說下針對某條邊，或某個交，膠量不夠的調試方法。在點擊密封配方進入后會顯示有向上密封，上部密封，向下密封，和下部密封，開始打膠的那條邊就是向上密封，然后順序從上。
The following is about the debugging method of insufficient glue for a certain edge or a certain intersection. After clicking the sealing formula to enter, it will display upward sealing, upper sealing, downward sealing, and lower sealing. The side where the glue is applied is upward sealing, and then the order is from top.
如果先打膠的這條邊，打膠不均勻，那么點擊向上密封，進入后顯示。掃描器開后發開的時間，就是在膠嘴貼到玻璃開始移動膠嘴出膠的時間，時間長出膠晚，時間短出膠早，掃描器開后開始移動的時間，就是膠嘴移動的速度，時間長移動慢，出膠多，時間短移動快出膠少。
If the gluing is uneven on the side where the glue is applied first, click up to seal, and it will be displayed after entering. The opening time of the scanner after opening is the time when the glue nozzle starts to move when it is pasted on the glass. The longer the time, the later the glue is released, the shorter the time, the earlier the glue is released. The time when the scanner starts to move after opening is the speed of the glue nozzle. The longer the time, the slower the movement, the more the glue is released, the shorter the time, the faster the movement, and the less the glue is released.
掃描膠量細微調整，就是只有某條邊膠少，或多，時調整掃描膠量細微調整，數值大膠量就大，數值小膠量就小。然后說下到末端伐關的距離，數值大，膠嘴到末端膠量少，數值小膠量大。
Fine adjustment of scanning glue amount is to adjust the scanning glue amount when there is less or more glue on a certain edge. If the value is large, the glue amount will be large, and if the value is small, the glue amount will be small. Then say the distance from the bottom to the end of the valve. If the value is large, the glue amount from the glue nozzle to the end is small, and if the value is small, the glue amount is large.
拐角時伐開的時間，就是控制拐角的膠量，數值大膠量大，數值小膠量小。如果拐角膠多就調小數值，拐角膠少，數值加大。
The cutting time at the corner is to control the glue amount at the corner. If the value is large, the glue amount is large, and if the value is small, the glue amount is small. If there is more corner glue, reduce the value. If there is less corner glue, increase the value.
Note that when adjusting the value, the value must be correct, the mixing must be uniform, and the pressure must be enough. After checking whether there is anything forgotten, wipe it clean and put it into use. For more information, please visit our website http://www.zlt89660896.com.cn Consult and understand.
上一篇：打膠機檢修小竅門必備技能
下一篇：打膠機在打膠中發生斷膠解決小妙招
