雙組份打膠機的當天使用完畢的事項
1、在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the operation of the machine on that day, the glue in the hose should be punched out to prevent hardening; if it is not practical for a long time, it should be noted to clean the hose and gun with kerosene.
2、雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。
2. The silicone glue or polysulfide glue used in the two-component beater should pay attention to the impurities can not be too high, low-quality glue is easy to plug the rubber pipe filtration system, resulting in unsmooth or uneven glue.
3、在更換膠的品種時要特別注意把雙組份打膠機內殘留的膠沖凈，好清洗，因為不同品種甚的膠容易反應堵塞機器。
3. When replacing the type of glue, special attention should be paid to the two-component glue beater to wash the residual glue, the best cleaning, because different varieties or even brands of glue easily react to block the machine.
4、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成事故。
4. The pressure of the hydraulic station system can not be adjusted too high, according to the indoor environment temperature and other actual conditions, adjust to meet the normal rubber nozzle glue evenly. Must open the glue gun when opening the hydraulic station, otherwise the pressure of B component pipeline will rise very high, causing safety accidents.
5、A膠提膠泵連續工作1分鐘以上沒有供膠停止，說明管路內有空氣，此時會報警，須打開泵上管接頭再打開A膠提膠泵，直到出膠為止，停止并接好接頭，膠槍會出現有空氣的嗶嗶爆破聲，空氣排凈就好了。
5. A glue pump working continuously for more than one minute without ceasing glue supply, indicating that there is air in the pipeline, at this time will alarm, to open the upper pipe connector of the pump and then open the A glue pump, until the glue is out, stop and connect the connector, the glue gun will appear to have the air beep explosion sound, air drain is good.
6、硅酮膠B 組份遇空氣會結殼，影響泵的正常工作和管路的暢通，因此，停機時B組份膠的所有通道在泄壓后均應關閉，使B組份不得接觸空氣。
6. Component B of silicone glue will crust when it meets the air, which will affect the normal operation of the pump and the smooth flow of the pipeline. Therefore, all channels of component B glue should be closed after pressure relief, so that component B can not touch the air.
7、正常工作時不要斷氣源，如果發現斷氣源應停止工作。
7, do not interrupt the source of gas when working normally. If you find the source of gas, you should stop working.
本文的精彩內容來自:
雙組份打膠機更多的詳細內容請點擊我們的網站：
http://www.zlt89660896.com.cn謝謝您的到來
The highlights of this article come from: For more details on the two-component dispenser, please click on our official website:
http://www.zlt89660896.com.cn. Thank you for coming.
上一篇：雙組份打膠機自身特點帶來的使用優勢
下一篇：真空灌膠機的這些特點你知道嗎？
