雙組份打膠機的使用安裝步驟
1、雙組份打膠機設備應安裝在干燥、無粉塵、無腐蝕性氣體的壞境中（該要求與其他設備一致，當然如果條件達不到少爭取無腐蝕性氣體，畢竟設備中有電線以及管路這些配件抗腐蝕性不高）。
1. Dual-component glue beater equipment should be installed in the dry, dust-free, non-corrosive gas environment (this requirement is consistent with other equipment, of course, if the conditions do not reach at least strive for non-corrosive gas, after all, the equipment has wires and pipelines these parts of the corrosion resistance is not high).
2、室內溫度好控制在10～40度的室內堅硬地面上，地面應水平度要好。（小編這里說的地面水平度要好不一定要非常的平整才行，我們的設備在設計之初已經考慮到了地面復雜性的因素所以對地面平整度是有相當大的忍讓度的，只要不是幅度提別的大一般都可以正常工作。）
2, indoor temperature is best controlled in 10~40 degree indoor hard ground, the ground should be better. The level of the ground is not necessarily very smooth. Our equipment was designed to take into account the complexity of the ground, so there is a considerable degree of tolerance for the level of the ground, as long as it is not a large range of other improvements can generally work properly.
3、雙組份打膠機安裝之前，應先檢查是否有因運輸、搬動造成的變形、損壞和緊固件松動情況，之前就曾經有客戶在移動打膠機的過程中把設備的智能控制系統的一個零部件碰掉了而導致設備無法正常運行，我們的工作人員到現場后才排查出的原因。
3. Before the installation of the two-component glue beater, we should check whether there is any deformation, damage and fastener loosening caused by transportation and moving. Before that, a customer knocked off a part of the intelligent control system of the equipment during the process of moving the glue beater, and the equipment could not run normally. Our staff arrived After the scene, the reasons for the investigation were found out.
4、我們可以根據地面平整度的實際情況來通過調整設備的可升降地腳螺栓來調整設備的水平度直到設備水平而穩固。然后按圖接線并可靠接地，把氣源接入機器所配帶的氣源接口，確保無漏氣現象。
4. Firstly, we can adjust the level of the equipment until the level of the equipment is stable by adjusting the liftable anchor bolts according to the actual situation of the ground levelness. Then according to the diagram wiring and reliable grounding, the air source into the machine with the air source interface, to ensure no leakage.
5、向油槽中加注液壓油指定位置，46#液壓油（約為50升左右）。
5, fill the tank with hydraulic oil to the specified position, 46# hydraulic oil (about 50 litres).
6、接通電源并打開查看設備是否能夠正常運行。
6, switch on the power and open the viewing device to operate normally.
That's what we're going to share. If you want to know more about it, please visit our official website at http://www.zlt89660896.com.cn, or search for our keyword binary dispenser. We'll have more wonderful content to share with you.
上一篇：中空玻璃設備保養知識須知
下一篇：雙組份打膠機的注意事項
